服务热线

021-39529830  021-39529839

您的位置:网站首页 > SMC气缸

    SMC进口薄型气缸,气缸SMC电子数据 产品名称:    SMC进口薄型气缸,气缸SMC电子数据
产品型号:MUB50-20DMZ
产品展商:日本SMC

详细介绍

    SMC进口薄型气缸,气缸SMC电子数据
    上海乾拓贸易有限公司
    企业QQ:2880626087
    电话;021-69001039
    手机;17321017802(微信)
    邮箱;17321017802@163.com
    地址:上海市嘉定区江桥嘉涌路99弄6号713室
    Refer to front matters 54 and 55 for Safety Instructions and pages 3 to 11 for Actuator and Auto Switch Precautions.
    Operating Precautions Caution 1. All loads to piston rod must be applied in axial direction only. 
    旋转精度非旋转杆六角截面形状活塞杆,具有高非旋转精度。 ?12,?16 - ±1°?20,?25 - ±0.7°
    Series CQS Specific Product Precautions Be sure to read before handling
    Also, tighten by giving consideration to prevent the tightening torque from being applied to the non-rotating guide.
    操作注意事项注意事项1.活塞杆的所有载荷只能在轴向上施加。 ?当不可避免地施加横向载荷时,请确保其不应超过图(1)至(5)中规定的杆端的允许横向载荷。 ?安装气瓶时,应精确定心。对于使用CQS作为止动器来防止非旋转活塞杆从侧向负载的情况,强烈建议采用引导机构。 2.当工件固定在活塞杆的端部时,确保活塞杆完全退回,并将扳手放在突出超过该部分的杆的部分上。此外,通过考虑防止紧固扭矩施加到非旋转引导件来收紧。
    固定环安装/拆卸注意事项1.安装和拆卸时,请使用适当的钳子(用于安装C型固定环的工具)。 2.即使使用适当的钳子(用于安装C型固定环的工具),也可能对人体或周边设备造成伤害,因为保持环可能会从钳子的尖端流出(用于安装C型固定环)。弹出一个挡环时要小心。此外,在安装之前,请确保在提供空气之前将固定环牢固地放在杆盖的槽中。
    Retaining Ring Installation/Removal Caution 1. For installation and removal, use an appropriate pair of pliers (tool for installing a type C retaining ring).
    2. Even if a proper plier (tool for installing type C retaining ring) is used, it is likely to inflict damage to a human body or peripheral equipment, as a retaining ring may be flown out of the tip of a plier (tool for installing a type C retaining ring). Be much careful with the popping of a retaining ring. Besides, be certain that a retaining ring is placed firmly into the groove of rod cover before supplying air at the time of installment.
    (Mounting orientation: Horizontal)
    CQS系列产品注意事项处理前务必阅读。有关执行器和自动切换注意事项,请参阅安全说明前面的事项54和55以及第3到11页。
    When a lateral load is applied unavoidably, ensure that it should not exceed the allowable lateral load to the rod end as specified in graph (1) to (5). 
    When installing a cylinder, centering should be required accurately. Adoption of guide mechanism is strongly recommended for the case when CQS is used as stopper to prevent non-rotating piston rod from side loads. 2. When a workpiece is secured to the end of the piston rod, ensure that the piston rod is retracted entirely, and place a wrench on the portion of the rod that protrudes beyond the section.
    Ideal for machine designs with small space requirements The “D-M9” auto switch will not protrude from switch mounting groove.
    Square body shape gives you flexibility for designing machine. Cross-section of a cylinder tube is the same configuration regardless of w/ switch or w/o switch.
    Auto switch mounting allows for flexible designing requirements 3 faces on ?12, ?16, and all 4 faces including port side on ?20, ?25.
    2 way basic mounting: Through-hole or both ends tapped Basic mounting is 2 way.  You can choose either through-hole or both ends tapped mounting.
    Non-rotating accuracy Non-rotating rod Hexagonal cross sectional shape piston rod for high non-rotation accuracy. ?12, ?16 - ±1° ?20, ?25 - ±0.7°
    用于空间要求较小的机器设计“D-M9”自动开关不会从开关安装槽突出。
    方形体形给您设计机器的灵活性。 气缸管的横截面是相同的配置,不管w /开关或w / o开关如何。
    自动开关安装允许灵活的设计要求?12,?16和所有4个面的3个面,包括端口侧?20,?25。
    2路基本安装:通孔或两端轻敲基本安装方式为2路。 您可以选择通孔或两端轻敲安装。

SMC进口薄型气缸,气缸SMC电子数据

在线客服